2022-04-10 12:29:44
| N0 | 英文 | 英文简写 | 中文 |
| 1 | ABSORBER | ABS | ABS防滑锁死 |
| 2 | ACCELERATOR | ACCEL | 油门(加速器) |
| 3 | ACCELERATOR | ACC | 附件（辅助的） |
| 4 | ACCUMULATOR | ACCUM | 蓄电器 |
| 5 | ACTUATING | ACTG | 起动器 |
| 6 | ACTUATOR | ACTR | 促动器 |
| 7 | ADAPTATION | ADAPT | 适应(改编) |
| 8 | ADAPTOR | ADPTR | 转接器 |
| 9 | ADDENDUM | ADD | 追加 |
| 10 | ADJUST | ADJ | 调整(对准) |
| 11 | ADJUSTMENT | ADJ | 调停 |
| 12 | ADVANCE | ADV | 提早装置 |
| 13 | AIR CLEANER | A/CLNR | 滤清器(空气) |
| 14 | AIR CONDITION | A/COND | 空气调节 |
| 15 | AIR CONDITIONING | A/C | 冷气 |
| 16 | AIR INLET | A/IN | 通气孔 |
| 17 | AIR OUTLET | A/OUT | 换气孔 |
| 18 | AIR SUSPENSION | A/SUSP | 气压式悬挂 |
| 19 | ALIGNMENT | ALIGN | 列队调准之行为 |
| 20 | ALLOWANCE | ALLOW | 扣除 |
| 21 | ALTERNATING CURRENT | AC | 交流电 |
| 22 | ALTERNATOR | AC | 发电机 |
| 23 | ALUMINUM | ALUM | 金名 |
| 24 | AMMETER | AMTR | 电流计 |
| 25 | AMPERE | AMP | 安培 |
| 26 | AMPLIFIER | AMPL | 增幅器 |
| 27 | ANCHOR | ANCH | 坚固可靠的支撑物 |
| 28 | AND | & | |
| 29 | ANNULUS | ANN | 环 |
| 30 | |||
| 31 | ANTENNA | ANT | 天线 |
| 32 | ANTI-RATTLER | A/RTLR | 伸缩天线 |
| 33 | ANTI-SQUEAK | A/SQK | 伸缩天线 |
| 34 | APPROVED | APVD | 被认可的 |
| 35 | APPROVING ENGINEER | A/ENGR | 工程师承认 |
| 36 | APPROXIMATE | APPROX | 接近(大概) |
| 37 | ARMREST | A/REST | 门侧扶手 |
| 38 | ARROWHEAD | A/HEAD | 箭头 |
| 39 | ASSEMBLY | ASSY | 组合件 |
| 40 | ATTACHING | ATT | 附着于 |
| 41 | AUTOMATIC | AUTO | 自动 |
| 42 | AUTOMATIC ADJUSTER | A/ADJ | 自动调节器 |
| 43 | AUTOMATIC CHOKE | A/CH | 自动活门 |
| 44 | AUTOMATIC TRANSMISSION | A/T | 自排 |
| 45 | AUTOMATIC TRANSMISSIONFLUID | ATF | 自排油 |
| 46 | AUXILIARY | AUX | 辅助的 |
| 47 | AVERAGE | AVG | 平均 |
| 48 | BACK | BK | (背部)底座 |
| 49 | BACK DOOR | B/DR | 后门 |
| 50 | BACKUP | B/UP | 后备 |
| 51 | BALANCE | BAL | 均衡平均 |
| 52 | BALL JOINT | B/JNT | 止阀头(指喷水器) |
| 53 | BALL STUD | B/STUD | 接头(指喷水器) |
| 54 | BATTERY | BATT | 电瓶 |
| 55 | BEARING | BRG | 支座 |
| 56 | BELLCRANK | B/CRK | 曲柄 |
| 57 | BIACK SIDE WALL | BSW | |
| 58 | BLOCK | BLK | |
| 59 | BLOWER | BLWR | 鼓风机 |
| 60 | BLUE PRINT | B/P | 蓝图,设计图 |
| 61 | BOARD | BRD | 板 |
| 62 | BOTTOM | BTM | 底(地基) |
| 63 | BRACKET | BRKT | 托架 |
| 64 | BRAKE | BRK | 煞车 |
| 65 | BRASS | BR | 黄铜 |
| 66 | BREAKER | BRKR | 水桶 |
| 67 | BRIGHT | BRT | 清晰的(光亮的) |
| 68 | BRONZE | BRZ | 青铜 |
| 69 | BUCKET | BKT | 活塞 |
| 70 | BUMPER | BMPR | 后动(保险杠) |
| 71 | BUSHING | BUSH | 轴视(绝缘套) |
| 72 | BUTTON | BTN | 电钮,按钮 |
| 73 | CABLE | CBL | 线束 |
| 74 | CAB OVER ENGINE | COE | 引擎转速 |
| 75 | CADMIUM | CAD | 镉 |
| 76 | CALCULATED WEIGHT | CAL/WT | 预先设定重量 |
| 77 | CANCEL | CANC | 取消 |
| 78 | CAPACITY | CAP | 客? |
| 79 | CARBURETOR | CARB | 化油器 |
| 80 | CARRIER | CARR | 搬运装置 |
| 81 | CARRY OVER | C/O | 运输 |
| 82 | CASTING | CSTG | 铸造物 |
| 83 | CAST IRON | C/IRON | 铸铁 |
| 84 | CATALOGUE | CAT | 目录 |
| 85 | CATHODE RAY TUBE | CRT | 阴极照射 |
| 86 | CENTER | CTR | 中心(指车头) |
| 87 | CENTERLINE | C/L | 中心线 |
| 88 | CENTERLINE OF FRONT SPRING EYE | FSE | |
| 89 | CENTER OF GRAVITY | CG | 重要 |
| 90 | CENTER PILLAR | C/PLR | 中心柱 |
| 91 | CENTER TO CENTER | C TOC | 中心 |
| 92 | CENTER WEIGHT | C/WT | 加重(中心) |
| 93 | CHAMBER | CHMBR | 室 |
| 94 | CHAMFER | CHAM | 柱子 |
| 95 | CHANGE | CHG | 改变 |
| 96 | CHANNEL | CHNL | 输水管 |
| 97 | CHARGING | CHG | 充电 |
| 98 | CHECK | CHK | 检查 |
| 99 | CHERK ARM | C/ARM | 检查臂 |
| 100 | CHECKED | CHKD | 格状花纹 |
| 101 | CHEMICAL SURFACE TREATMENT | CSTG | 化学表面处理 |
| 102 | CHOKE | CH | 活门(阻塞) |
| 103 | CHROME | CHR | 黄的 |
| 104 | CHROME BRIGHT | C/BRT | 亮的黄粉 |
| 105 | CHRYER | CHRY | 克莱斯靳 |
| 106 | CHRYSLER ALUMINUM FINISH | CAF | |
| 107 | CHRYSLER ENGINEERING STANDARD | CES | 克莱斯靳工程师标准 |
| 108 | CHRYSLER LABORATORY PROCEDURE | CES | 实验室程序 |
| 109 | CHRYSLER PATTERN MATERIAL | CPM | 材料的标准 |
| 110 | CHRYSLER PLASTIC NUMBER | CPN | 造型总数 |
| 111 | CHRYSLER PLATED FINISH | CPF | |
| 112 | CIGARETTE LIGHTER | C/LTR | 点烟器 |
| 113 | CIRCUIT BOARD | C/BRD | 电路板 |
| 114 | CIRCUIT BREAKER | C/BRKR | 电路板 |
| 115 | CIRCULAR PITCH | CP | |
| 116 | CIRCUMFERENCE | CIRCUM | 园周 |
| 117 | CLASS | CL | 等级 |
| 118 | CLASSIFCATION | CLASS | 分类 |
| 119 | CLEANER | CLNR | 滤水器 |
| 120 | CLEARANCE | CLNC | 清除(交换) |
| 121 | CLNCH NUT | C/NUT | 螺帽 |
| 122 | CLOCKWISE | C/WISE | 顺时针,右转的 |
| 123 | CLOSURE | CLSR | 截止 |
| 124 | CLUTCH | CL | 离合器 |
| 125 | COCKPIT | CKPT | 驾驶舱 |
| 126 | COEFFICIENT | COEF | 共用 |
| 127 | COLD ROLLED STEEL | CRS | |
| 128 | COLLMATOR | COLMTR | 准直(平行) |
| 129 | COLUMN | COLMTR | 圆柱 |
| 130 | COMBINATION | COMB | 结合 |
| 131 | COMBSTION | COMBN | 燃烧(氧化) |
| 132 | COMMUTATOR | CMTR | 空流器 |
| 133 | COMMUTATOR END | C/E | 结束整流器 |
| 134 | COMPARTMENT | COMPT | 间隔(舱) |
| 135 | COMPLETE | COMPL | 完全的,圆满的 |
| 136 | COMPLETELY KNCCKED DOWN | CKD | 完全, |
| 137 | COMPONENT | COMP | 成分,构造 |
| 138 | COMPRESSION | COMPR | 压缩 |
| 139 | COMPRESSOR | COMPR | 压缩机 |
| 140 | CONCENTRIC | CONC | 集中性的 |
| 141 | CONDENSER | COND | 蓄电池 |
| 142 | CONDUIT | CNDT | 导管,水管 |
| 143 | CONNECTING | CONNG | 结合,连接 |
| 144 | CONNECTING ROD | C/ROD | 连接棒 |
| 145 | CONNECTOR | CONN | 连接插头 |
| 146 | CONSTANT | CONST | 坚固 |
| 147 | CONSTRUCT | CONST | 设计(作图) |
| 148 | CONTAINER | CONTNR | 容器 |
| 149 | CONTOUR | CTR | 轮廓 |
| 150 | CONTROL | CONTNR | 驾驶(控制) |
| 151 | CONTROL VALVE | C/VAL | 以活门调节 |
| 152 | CONVERTER | CONV | 变换器,交换器 |
| 153 | CONVERTIBLE | CV | |
| 154 | COORDINATE | COORD | 同等分 |
| 155 | CORNER | COR | 角(转弯) |
| 156 | COTTER PIG | COT/PIN | |
| 157 | COUNTER BORE | C/BORE | 靠计算器 |
| 158 | COUNTERCLOCKWISE | CC/WISE | 逆时钟 |
| 159 | COUNTER DAILL | C/DRILL | 训练计算机 |
| 160 | COUNTER PUNCH | C/PUNCH | 训练用打孔器 |
| 161 | COUNTERSHAFT | CO/SHAFT | 轴心 |
| 162 | COUNTERSINK | C/SINK | |
| 163 | COUNTERWEIGHT | CO/WT | 重量 |
| 164 | COUPLING | CPLG | 联络器 |
| 165 | COUPRTESY LAMP | C/LP | 室内照明灯 |
| 166 | COVER | CVR | 盖子 |
| 167 | COWL VENTILATOR | C/VENT | 通风孔 |
| 168 | CRANKCASE | C/CASE | 曲轴箱 |
| 169 | CRANKSHAFT | CK/SHAFT | 曲轴心 |
| 170 | CROSSMENBER | C/MBR | 效凹处 |
| 171 | CROSS SHAFT | C/SHAFT | 效轴 |
| 172 | CURRENT REGULATOR | C/REG | 流动调节器 |
| 173 | CUSHION | CUSH | 垫子 |
| 174 | CUSTOM | CUST | 习惯 |
| 175 | CYLINDER | CYL | 汽缸 |
| 176 | DAMPER | DMPR | 消音器 |
| 177 | DAYLIGHT OPENING | DLO | 白天开启的 |
| 178 | DECALCOMANIA | DECAL | 转印 |
| 179 | DECOMPRESSION | DECOMP | 减压 |
| 180 | DEDENDUM | DED | |
| 181 | DEFLECTOR | DEFL | 变流装量 |
| 182 | DEFOGGER | DEFOG | 除雾器 |
| 183 | DEFROSTER | DEF | 防结水装置 |
| 184 | DELUXE | DLX | 高级,豪华的 |
| 185 | DEPARTMENT | DEPT | 部门 |
| 186 | DETAIL | DTL | 详细 |
| 187 | DIAGONAL | DIAG | 对角线(斜线) |
| 188 | DIAGRAM | DIAG | 图示 |
| 189 | DIAMETER | DIA | 直径(径率) |
| 190 | DIAMETRICAL PITCH | DP | 直径 |
| 191 | DIAPHRAGM | DIAPH | 隔板 |
| 192 | DIFFERENTLAL | DIFF | 差别的 |
| 193 | DIMENSION | DIM | 尺寸 |
| 194 | DIMMER SWITCH | D/SW | 调光器开关 |
| 195 | DIRECT | DIR | 正统的 |
| 196 | DIRECT CLUTCH | D/CL | 正确的踩离器 |
| 197 | DIRECT CURRENT | DC | 正确的流动 |
| 198 | DISCHARGE | DISCH | |
| 199 | DISTANCE | DIST | 距离(差别) |
| 200 | DISTRIBUTOR | DIST | 分配(分电盘) |
| 201 | DIVISION | DIV | 分割 |
| 202 | DOME LAMP | D/LP | 室内顶灯 |
| 203 | DOMESTIC | DOM | 家庭的 |
| 204 | DO NOT SERVICE | DNS | 不作服务 |
| 205 | DOOR | DR | 门 |
| 206 | DOUBLE | DBL | 双倍 |
| 207 | DOWEL | DWL | 双尖钉 |
| 208 | DRAGLINK | D/LINK | 拉环 |
| 209 | DRAWING | DWG | 图形 |
| 210 | DRAWING CHANGE NOTICE | DCN | 图形变更通知 |
| 211 | DRAWN | DWN | |
| 212 | DRIVE | DRV | 驾驶过(过去式) |
| 213 | DRIVE PINION | D/PINION | 驾驶的尖端 |
| 214 | DRIVER SEAT | D/SEAT | 驾驶边的座椅 |
| 215 | DUAL EXHAUST | D/EXH | 双重排气 |
| 216 | DUST COVER | D/CVR | 防尘盖 |
| 217 | DUST SEAL | D/SEAL | 保证高压 |
| 218 | DUST SHIELD | D/SHLD | 防尘罩 |
| 219 | EARTH | E | 接地 |
| 220 | ECCENTRIC | ECC | 离心圆 |
| 221 | ECONOMY | ECON | 经济,节约 |
| 222 | EFFECTIVE | EFFEC | 有效的,实际的 |
| 223 | ELVOW | ELL | 扶手 |
| 224 | ELECTRIC | ELEC | 升电机 |
| 225 | ELECTRONIC CONTROL AUTOMATIC TRANSMISSION | EAT | 电子控制自排 |
| 226 | ELIMINATOR | ELLM | 整流器 |
| 227 | ELONGATION | ELONG | 伸张度 |
| 228 | EMERGENCY | EMERG | 紧急状态(事故) |
| 229 | EMNGINE | ENG | 引擎 |
| 230 | ENGINEER | ENGR | 工程师 |
| 231 | ENGINEERING | ENGRG | 工程 |
| 232 | ENGINEERING CHANGE REQUEST | ECR | 工程变更需求 |
| 233 | ENGINEERING ORDER | EO | 工程命令 |
| 234 | ENGINEERING PARTS LIST | EPL | 工程变零件清单 |
| 235 | EQUIPMENT | EQUIP | 装置,设备 |
| 236 | ESCUTCHEON | ESC | |
| 237 | ESTIMATE | EST | 估计,估价单 |
| 238 | EVAPORATION | EVAP | 干燥,蒸气 |
| 239 | EVAPORATOR | EVAP | 蒸发器,干燥器 |
| 240 | EVAPORATOR CONTROL SYSTEM | ECS | 蒸发器/干燥器控制系统 |
| 241 | EXHAUST | EXH | 消耗/排气 |
| 242 | EXHAUST GAS RECIRCULATION | EGR | |
| 243 | EXPANSION | EXPN | 膨胀,扩展,宽度 |
| 244 | EXPERIMENTAL | EXPL | |
| 245 | EXPORT | EXP | 输出 |
| 246 | EXTENSION | EXT | 扩大,伸展 |
| 247 | EXTERIOR | XET | 表面的,外部的 |
| 248 | EXTERNAL | EXTL | 外界,表面的 |
| 249 | EXTRA | EX | 特别的,额外的 |
| 250 | EXTRUDED | EXTR | |
| 251 | |||
| 252 | [F] | ||
| 253 | FACTORY | FACT | 制造厂 |
| 254 | FASTENER | FASTNR | |
| 255 | FASTENING | FSTNG | 拴牢,紧结物 |
| 256 | FENDER | FNDR | 挡泥板 |
| 257 | FLELD | FLD | |
| 258 | FIFTH | STH | 第5(5分之一) |
| 259 | FIGURE | FIG | 数字,计算 |
| 260 | FILTER | FIL | 过滤器 |
| 261 | FINISH | FIN | 结束 |
| 262 | FINISH ALL OVER | FAO | 全部结束 |
| 263 | FINISH MOULDING | F/MLDG | 结束模式 |
| 264 | FIRE EXTNGUISHER | F/EXTG | 灭火器 |
| 265 | FIRST | IST | 首先(第一) |
| 266 | FITTING | FTG | 试装(配件) |
| 267 | FLANGE | FLG | 边缘,凸缘 |
| 268 | FLAT | FL | 平的 |
| 269 | FLEXIBLE | FLEX | 柔软的 |
| 270 | FLOOR | FLR | 地板 |
| 271 | FLOOR BOARD | F/BRD | 地板，板面 |
| 272 | FLOOR PAN | F/PAN | 地板凹槽 |
| 273 | FLUID COUPLING | F/CPLG | 流体,连结器 |
| 274 | FLYWHEEL | F/WHL | 调速轮 |
| 275 | FOLDING TOP | F/TOP | 折叠,顶盖 |
| 276 | FOOT | FT | 底部 |
| 277 | FORGING | FORG | 锻练 |
| 278 | FORWARD | FWD | 前面的 |
| 279 | FOUNDATION | FOUND | 基础 |
| 280 | FOURTH | 4TH | 第4(4分之1) |
| 281 | FRAME | FRM | |
| 282 | FRESH AIR | F/AIR | 新鲜空气 |
| 283 | FRONT | FR | 前面 |
| 284 | FRONT AXLE | F/AXLE | 前轮轴 |
| 285 | FRONT DOOR | F/DR | 前门 |
| 286 | FRONT FLOOR | F/FLR | 前地板 |
| 287 | FRONT OF DASH | FOD | ? |
| 288 | FRONT PILLAR | F/PLR | 前柱(A柱) |
| 289 | FRONT SEAT | F/SEAT | 前座椅 |
| 290 | FUEL FILTER | F/FILT | 滤油器 |
| 291 | FUEL GARGE | F/GA | 油量表 |
| 292 | FUEL INJECTION | F/INJ | 喷射供油 |
| 293 | FUEL PUMP | F/PUMP | 供油线轴 |
| 294 | FUEL TANK | F/TANK | 油箱(桶) |
| 295 | |||
| 296 | [G] | ||
| 297 | GALVANIZED | GALV | 镀锌 |
| 298 | GARNISH | GARN | 装饰 |
| 299 | GARNISH MOULDING | G/MLDG | 装饰模式 |
| 300 | GASKET | GSKT | |
| 301 | GASOLINE | GAS | 汽油 |
| 302 | GATE PILLAR | G/PLR | 门柱 |
| 303 | GAUGE | GA | 计量器 |
| 304 | GEAR | GR | |
| 305 | GEARSHIFT | G/SHIFT | 排档齿轮 |
| 306 | GENERAL LIST | GL | 一般目录 |
| 307 | GENERATOR | GEN | |
| 308 | GENERATOR REGULATOR | G/REG | |
| 309 | GLASS | GLA | 玻璃 |
| 310 | GLOVEBOX | G/BOX | |
| 311 | GOVERNOR | GOV | 速度表(仪) |
| 312 | GRILLE | GRL | |
| 313 | GROMMET | GROM | 胶套 |
| 314 | GROUND | GRD | 接地 |
| 315 | GRPRP | GR | |
| 316 | |||
| 317 | [H] | ||
| 318 | HANDLE | HDLE | 柄 |
| 319 | HARNESS | HARN | 线束 |
| 320 | HATCH BACK | H/BACK | 后门 |
| 321 | HEAD | HD | (前端) |
| 322 | HEADER | HDR | 前端,方 |
| 323 | HEADLAMP | H/LP | 头灯,大灯 |
| 324 | HEADLINING | H/LIN | 灯座(内视) |
| 325 | HEADRESTRAINT | H/REST | 前灯控制 |
| 326 | HEATER | HTR | 加热器 |
| 327 | HEAT SHIELD | H/SHLD | 散热排 |
| 328 | HEAVY | HVY | 重的,猛烈的 |
| 329 | HEAVY DUTY | H/DRTY | 耐用(强化) |
| 330 | HEIGHT | HGT | 高度 |
| 331 | HEXAGON | HEX | 六角形 |
| 332 | HIGH | HI | 高 |
| 333 | HIGH COMPRESSION | H/C | 高压缩 |
| 334 | HIGH PERFORMANCE | H/PERF | |
| 335 | HIGH TENSION | H/T | 高拉力 |
| 336 | HINGE | HGE | 交链 |
| 337 | HORIZONTAL | HORIZ | 水平线 |
| 338 | HOUSING | HSG | 胶盒 |
| 339 | HYDRAULIC | HYD | 水力的,用水的 |
| 340 | IDENTIFICATION | IDENT | 确认 |
| 341 | IDLER ARM | I/ARM | 不动摆臂(间) |
| 342 | IDLER GEAR | I/GEAR | 不动车轮(间) |
| 343 | IDLER PULLEY | I/PULL | 不动滑轮 |
| 344 | IGNITION | IGN | 点火电 |
| 345 | INCLUDE | INCL | 包含 |
| 346 | INDICATOR | IND | 批示器 |
| 347 | INDICATOR LAMP | I/LP | 批示灯 |
| 348 | INDUSTRIAL | IND | 工业的 |
| 349 | INFORMATION | INFO | 情报 |
| 350 | INJECTION | INJ | 喷射 |
| 351 | INLET | INL | 入口,通道 |
| 352 | INNER | INR | 内部 |
| 353 | INSIDE | I/S | 车内的 |
| 354 | INSIDE DIAMETER | ID | 车内空间 |
| 355 | INSPECTION | INSP | 点检 |
| 356 | INSTALLATION | INSTAL | 安装 |
| 357 | INSTALLED | INSTAL | 指令,通知 |
| 358 | INSTRUCT | INSTR | 仪器 |
| 359 | INSTRUCTION | INSTR | 指令,通知 |
| 360 | INSTRUMENT | INST | 仪器 |
| 361 | INSTRUMENT PANEL | I/PNL | 仪表板 |
| 362 | INSULATE | INSUL | 隔离,绝缘 |
| 363 | INSULATION | INSUL | 隔离,绝缘 |
| 364 | INSULATOR | INSUL | 绝缘体 |
| 365 | LITAKE | INT | 通风口 |
| 366 | INTEGRATED CIRCUIT | I/C | 整合回路 |
| 367 | INTERCHANGEABLE | INTCHG | 可交换的 |
| 368 | INTERIOR | INT | 内部的 |
| 369 | INTERLOCK | INTLK | 内部锁 |
| 370 | INTERMEDIATE | INTER | 中控 |
| 371 | INTERMITTENT | INT | 间歇的 |
| 372 | INTERNAL | INTL | 内藏的 |
| 373 | SEAT BACK | S/BACK | 座背 |
| 374 | SEAT BELT | S/BELT | 安全带 |
| 375 | SEAT CUSHION | S/CUSH | 座椅垫 |
| 376 | SECOND | 2ND | 副的 |
| 377 | SECONDARY | SECDY | 第二的，代理的 |
| 378 | SECTION | SECT | 片、块 |
| 379 | SELECTOR | SEL | 选择、分离器 |
| 380 | SEPARATE | SEP | 分隔、分割 |
| 381 | SEQUENCE | SEQ | 顺序 |
| 382 | SERVICE | SERV | 服务 |
| 383 | SHIELD | SHLD | 保护的、挡片 |
| 384 | SHOCK ABSORBER | S/ABS | 防滑锁死、系统 |
| 385 | SIDE MARKER | S/MRK | 侧面标志 |
| 386 | SIDE MEMBER | S/MBR | 侧部位 |
| 387 | SIDE PANEL | S/PNL | 侧门板 |
| 388 | SIDE RAIL | S/RAIL | 侧门把 |
| 389 | SIDE SHIELD | S/SHLD | 侧门板 |
| 390 | SIDE SILL | S/SILL | 侧门框 |
| 391 | SIGNAL | SIG | 信号 |
| 392 | SINGLE EXHAUST | S/EXH | 油料警示 |
| 393 | SINGLE SPEED | S/SPD | 速度警示 |
| 394 | SIXTH | 6TH | 第六/6/1 |
| 395 | SLEEVE | SLV | 套筒 |
| 396 | SLIDING | SLDG | 滑、滑动的 |
| 397 | SLOTTED | SLTD | 水沟 |
| 398 | SNAP RING | S/RING | |
| 399 | SOCKET | SOC | 插座 |
| 400 | SOLENOID | SOL | 线圈 |
| 401 | SPEAKER | SPKR | 扩音器 |
| 402 | SPECIAL | SPL | 特别 |
| 403 | SPECIFIC GRAVITY | SP/GP | 特别重大 |
| 404 | SPECIFICATION | SPEC | 规格说明 |
| 405 | SPEEDOMETER | SPEEDO | 时速表 |
| 406 | SPHERICAL | SPHER | 球面的 |
| 407 | SPLASH SHIELD | SP/SHLD | 挡泥板 |
| 408 | SPRING | SPG | 春、动力 |
| 409 | SPROCKET | SPRKT | 扣链齿轮 |
| 410 | SQUARE | SQ | 正方形 |
| 411 | STABILIZER | STAB | 固定装置 |
| 412 | STAINLESS STEEL | S/STL | 不锈钢 |
| 413 | STANDARD | STD | 标准 |
| 414 | STARTER | STRTR | 起动器 |
| 415 | STATION | STA | 站 |
| 416 | STATIONARY | STAT | 不动的 |
| 417 | STEEL | STL | 钢 |
| 418 | STEERING | STRG | 操纵（转向） |
| 419 | STEERING GEAR | S/GR | 转向齿轮 |
| 420 | STEERING KNUCKLE | S/KNU | 转向接头 |
| 421 | STIFFENER | STIFR | 补强用材料 |
| 422 | STOP LAMP | S/LP | 刹车灯 |
| 423 | STRAIGHT | STRG | 笔直的 |
| 424 | STRAINER | STRNR | 过滤器 |
| 425 | STRIKER | STRKR | 撞针 |
| 426 | STRUCTURE | STRUC | 结构、构造 |
| 427 | SUCTION | SUCT | 吸、抽气、通风 |
| 428 | SUFFIX | SUFF | 分指数 |
| 429 | SUPERSEDED | SUPD | 代替 |
| 430 | SUPPORT | SUPT | 支撑 |
| 431 | SURFACE | SURF | 表面 |
| 432 | SUSPENSION | SUSP | 悬挂（避震器） |
| 433 | SWITCH | SW | 开关 |
| 434 | SYMBOL | SYM | 象征、标志 |
| 435 | SYMMETRICAL | SYMM | 对称性的 |
| 436 | SYNCHRONIZE | SYNCH | 同时发生 |
| 437 | SYNCHRONIZER | SYNCH | 同步装置 |
| 438 | SYNCHRONIZING | SYNCHG | 同步 |
| 439 | SYNTHETIC | SYNTH | 合成的 |
| 440 | SYSTEM | SYS | 系统 |
| 441 | |||
| 442 | |||
| 443 | （T） | ||
| 444 | TACHOMETER | TACHO | 转速计 |
| 445 | TAILGATE | T/GATE | 尾门 |
| 446 | TAIL LAMP | T/LP | 尾灯 |
| 447 | TANDEM | TNDM | 直排 |
| 448 | TAPPING | TAP | 轮拍 |
| 449 | TEMPERATURE | TEMP | 温度 |
| 450 | TEMPERATURE GAUGE | T/GA | 温度计 |
| 451 | TERMINAL | TERM | 端子 |
| 452 | TERMINAL BLOCK | T/BLK | |
| 453 | THERMAL REACTOR | T/R | 热 |
| 454 | THERMOSTAT | THERMO | 自动调温器 |
| 455 | THICK | THK | 厚的 |
| 456 | THIRD | 3RD | 第三 |
| 457 | THREAD | THD | 线状物 |
| 458 | THROTTLE | THROT | 节气阀 |
| 459 | THROTTLE CONTROL | T/CONT | 控制阀 |
| 460 | TOLERANCE | TOL | 公差 |
| 461 | JOINT | JNT | 接线 |
| 462 | JUNCTION BLOCK | J/BLK | 接线区 |
| 463 | KICKDOWN | K/DN | 动踏 |
| 464 | KICKUP | K/UP | 动提 |
| 465 | KNOCKDOWN | KD | 爆震 |
| 466 | KNOCKED DOWN FOR EXPORT | KDX | 动输出 |
| 467 | KNUCKLE | KNU | 关节 |
| 468 | LAMP | LP | 灯 |
| 469 | LEAN | LN | 转向 |
| 470 | LEET | LT | 左 |
| 471 | LEET HAND | LH | 左向 |
| 472 | HEET HAND DRIVE | LHD | 左驾驶 |
| 473 | LENGTH | LG | 长度 |
| 474 | LETTER | LTR | 信,字母 |
| 475 | LEVER | LVR | 杠杆,工具 |
| 476 | LICENSE | LIC | 执照,牌照 |
| 477 | LIGHTER | LTR | 点火器 |
| 478 | LIMIT | LIM | 限速 |
| 479 | LIMITED | LTD | 限速器 |
| 480 | LINING | LIN | |
| 481 | LIQUID | LIQ | 液体 |
| 482 | LOCATING | LOC | 设置，居住 |
| 483 | LOCK | LK | 锁 |
| 484 | LOCKING | LKG | 锁 |
| 485 | LOCK NUT | LK/NUT | 螺母 |
| 486 | LOCK WASHER | LK/WA | 固定冲洗 |
| 487 | LOW | LO | 低 |
| 488 | LOW COMPRESSION | L/C | 低压 |
| 489 | LOWER | LWR | 降下 |
| 490 | LOW TENSION | L/T | 低拉力 |
| 491 | LUBRICANT | LUB | 润滑油 |
| 492 | LUBRICATING | LUB | |
| 493 | LUGGAGE | LUGG | 行李 |
| 494 | LUGGAGE COMPARTMENT | L/COMPT | 行李箱 |
| 495 | MACHINE | MACH | 机械 |
| 496 | MAGNET | MAG | 磁铁 |
| 497 | MAINTENANCE | MAINT | 保存 |
| 498 | MALLEALEIRON | M/IRON | 软金属 |
| 499 | MANIROLD | MANF | |
| 500 | MANUAL | MANF | 手册 |
| 501 | MANUAL ADJUSTING | M/ADJ | 调整，维修手册 |
| 502 | MANUAL BRAKE 手刹车 | M/BRK | |
| 503 | MANUAL CHOKE 引薄 | M/CH | |
| 504 | MANUAL TRANSMISSION 变速器 手动 | M/T | |
| 505 | MANUFACTURING 制造(工业) | MFG | |
| 506 | MASTER CYLINDER 主汽 | M/CYL | |
| 507 | MATERLAL 原料、材料 | MATL | |
| 508 | MAXIMUM 最大、 | MAX | |
| 509 | MAXIMUM MATERIAL CONDITON 最大承受状态 | MMC | |
| 510 | MECHANISM 机械 | MECH | |
| 511 | MEDIUM 普通的 | MED | |
| 512 | MEMBER 构材 | MBR | |
| 513 | METERING 仪表 | MTRG | |
| 514 | MINIMUM 最小 | MIN | |
| 515 | MISCELLANEOUS 多方面的 | MISC | |
| 516 | MITSUBISHI MOTORS CORPORATION | MMC | |
| 517 | MODEL 模式 | MOD | |
| 518 | MODIFICATION 修正 | MOD | |
| 519 | MODULATOR 调幅器 | MODUL | |
| 520 | MOTOR 马达 | MRT | |
| 521 | MOULDING 模2、模型 | MLDG | |
| 522 | MOUNT 手动 | MT | |
| 523 | MOUNTING 架设 | MTG | |
| 524 | MUFFLER 消音器 | MUFF | |
| 525 | MULTIPLE DISC CLUTCH | MDC | |
| 526 | 离合器 | ||
| 527 | [N} | ||
| 528 | NAME PLATE 电镀名牌 | N/PLT | |
| 529 | NEGATIVE | NEG | |
| 530 | NEIOTAL 不带电 | NEUT | |
| 531 | NOMINAL | NOM | |
| 532 | NORMAL 标准 普通 | NORM | |
| 533 | NOT AVAILABLE 失效 | N/A | |
| 534 | NOZZLE 喷嘴 | NOZ | |
| 535 | NUMBER 数字、号码 | NO | |
| 536 | OIL GAUGE | O/GA | 油表 |
| 537 | OIL PUMP | O/PUMP | 油泵 |
| 538 | ONE WAY CLUTCH | OWC | 单向离合器 |
| 539 | OPENING | OPNG | 开启 |
| 540 | OPERATING | OPER | 运转 |
| 541 | OPPOSITE | OPP | 相反 |
| 542 | OPTIONAL | OPT | 选项的 |
| 543 | OPIGINAL | ORIG | 制作 |
| 544 | ORNAMENT | ORN | 装饰 |
| 545 | OUTER | OTR | 外观 |
| 546 | OUTLET | OUTL | 出口 |
| 547 | OUTSIDE | O/S | 外侧 |
| 548 | OUTSIDE DIAMETER | OD | 外观空间 |
| 549 | OVAL | OV | 图型 |
| 550 | PVERALL | O/A | 全部 |
| 551 | OVERDROVE | O/D | 省油档 |
| 552 | OVERHAUL | O/H | 精密 |
| 553 | OVERRUNNING | O/RUN | 超载 |
| 554 | OVERSIZE | O/SIZE | 特大的 |
| 555 | OVER TO | O/T | 超出 |
| 556 | OVERWRAT | O/WRAP | 保鲜膜 保护膜 |
| 557 | PACKAGE | PKG | 包装 |
| 558 | PACING | PACK | 包装物 |
| 559 | PAGE | P | 页 |
| 560 | PAINT | PNT | 油漆 |
| 561 | PAINTED | PNTD | 著色的 |
| 562 | PANEL | PNL | 面板 |
| 563 | PARALLEL | PAR | 平行线 |
| 564 | PARKING | PARK | 停车 |
| 565 | PARLOMG BRALE | PK/BRK | 手刹车 |
| 566 | PARKING LAMP | P/LP | 停车灯 |
| 567 | PARTIAL | PARTL | 部分的 |
| 568 | PARTLAL | PARTN | 侵害、分配 |
| 569 | PARTS LIST | PL | 零件清单 |
| 570 | PASSENGER | PASS | 旅客 |
| 571 | PASSENGER SEAT | P/SEAT | 旅客座椅 |
| 572 | PATENT | PAT | 专利、专用的 |
| 573 | PATTERN | PATT | 模范 |
| 574 | PEDAL | PED | 踏板 |
| 575 | PERFORMANCE | PERF | 执行 |
| 576 | PERPENDICULAR | PERP | 垂直的 |
| 577 | PIEPCE NUT | PRC/NUT | 螺帽 |
| 578 | PILLAR | PLR | 柱 |
| 579 | INION | PIN | 小龄轮 |
| 580 | PISTON | PIST | 活塞 |
| 581 | PITCH | P | 历青 |
| 582 | PITCH CIRCLE | PC | 范围 |
| 583 | PITCH DIAMETER | PD | |
| 584 | PIVOT | PIV | 轴 |
| 585 | PLAIN | PL | 平坦的 |
| 586 | PLAIN WASHER | PL/WA | 平坦／洗 |
| 587 | PLATE | PLT | 车牌，牌照 |
| 588 | PLATED | PLTD | 镀金，装甲的 |
| 589 | PLUMBING | PLUMB | 管类 |
| 590 | PLUNGER | PLUNG | 动入物 |
| 591 | PNEUMATIC | PNEU | 气动的，充气的 |
| 592 | POINT | PT | 点火器 |
| 593 | POINT ON LING | POL | |
| 594 | POSITON | POSN | 位置，地点姿势 |
| 595 | POSITIVE | POS | 确定 |
| 596 | POTENTIOMETER | P/MTR | 电位钉／分压计 |
| 597 | POWER | PWR | 动力 |
| 598 | POWER BRAKE | P/BRK | 动力刹车 |
| 599 | POWER STEERING | P/S | 动力方向盘 |
| 600 | POWER TAKE OFF | PTO | 动力脱下 |
| 601 | PRESSURE | PRESS | 压／压力 |
| 602 | PRESSURE ANGLE | PA | 施压力角度 |
| 603 | PRIMARY | PRIM | 主要的／基本的 |
| 604 | PRODUCTION | PROD | 制作／方案 |
| 605 | PROJECT | PROJ | 企划／方案 |
| 606 | PROPELLER | PROP | 螺旋桨 |
| 607 | PROTECTOR | PROT | 护板 |
| 608 | PROTOTYPE | PROT | 原型／标准 |
| 609 | PURCHASED | PURCH | 用起重装置举起／移动 |
| 610 | PUSH BUTTON | P/BTN | 推／按钮 |
| 611 | PUSH ROD | P/ROD | 推杆 |
| 612 | QUALITY | QUAL | 品质 |
| 613 | QUANTITY | QTY | 数量 |
| 614 | QUARTER | QTR | ４分之一／４等分 |
| 615 | QUARTER PANEL | Q/PNL | 配电盘 |
| 616 | QUARTER WINDOW | Q/WDO | 副窗户 |
| 617 | RADIATOR | RAD | 冷却器 |
| 618 | RADIO | RDO | 收音机 |
| 619 | RADIUS | R | 半径／范围 |
| 620 | REACTION | REACT | 反应／感应 |
| 621 | REAR | RR | 后，后部 |
| 622 | REAR AXLE | R/AXLE | 后轮轴 |
| 623 | REAR DOOR | R/DR | 后，车门 |
| 624 | RAEA FLOOR | R/FLR | 后地板 |
| 625 | REAR PILLAR | R/PLR | 后门栓 |
| 626 | REAR QUARTER | R/QTR | 后压 |
| 627 | REAR SEAT | R/SEAT | 后座 |
| 628 | REAR SHAFT | R/SHAFT | 后轴心 |
| 629 | REAR WINDOW | R/WDO | 后窗户 |
| 630 | RECEIVER | REC | 接收器 |
| 631 | RECIRCULATION | RECIRC | |
| 632 | RECTIFIER | RECTR | 整流器 |
| 633 | REDUCTION | RED | 换算 |
| 634 | REFERENCE | REF | 参照 |
| 635 | REFLECTOR | REFL | 反射 |
| 636 | REFLEX REFLECTOR | R/R | 反射体 |
| 637 | REFRIGERANT | REFR | 冷却剂 |
| 638 | REGULATOR | REG | 调节器 |
| 639 | REINFORCEMENT | REINF | 辅强材料 |
| 640 | RELAY | RLY | 继电器 |
| 641 | RELEASE | REL | 释放 |
| 642 | REMOTE | REM | 细微的 |
| 643 | REMOTE CONTROL | R/CONT | 微小胶盒 |
| 644 | REMOVED | RMVD | 间隔的 |
| 645 | REPLACES | REPL | 代替 |
| 646 | REQUIRED | REQD | 必修的 |
| 647 | RESISTANCE | RES | 电阻 |
| 648 | RESISTOR | RES | 电阻 |
| 649 | RESTRICT | REST | 限制，制止 |
| 650 | RETAIN | RET | 保持 |
| 651 | RETAINER | RET | 保持者 |
| 652 | RETURN | RETN | 返回，归 |
| 653 | REVERSE | REV | 反转，颠倒 |
| 654 | REVISED | REVD | 经过修订 |
| 655 | REVOLUTIONS PER MINUTE | RPM | 引擎转速 |
| 656 | REVOLUTIONS PER SECOND | RPS | 副转速 |
| 657 | RHEOSTAT | RHEO | 变阻器 |
| 658 | RIGHT | RT | 右的 |
| 659 | RIGHT HAND | RH | 右方向灯 |
| 660 | RIGHT HAND DRIVE | RHD | 驾驶向灯 |
| 661 | ROUND | RD | 圆形 |
| 662 | RUBBER | RUB | 合成橡胶 |
| 663 | RUNNING | RUNN | 液体的 |
| 664 | RUNWAY | RWY | 通路 |
| 665 | SCHEDULE | SCH | 目录 |
| 666 | SCREW | SC | 螺丝 |
| 667 | SEAT | ST | 座椅 |
| 668 | TONGUE WASHER | TOG/WA | 舌状环 |
| 669 | TORQUE | TORQ | 扭力 |
| 670 | TORQUE CONVERTER | T/CONV | 扭力转换器 |
| 671 | TORSION BAR | T/BAR | 扭力棒 |
| 672 | TOTAL INDICATOR READING | TIR | 总指示器 |
| 673 | TRANSACTION | TR | 处理(记录) |
| 674 | TRANSFER | T/F | 转移 |
| 675 | TRANSISITOR | TSTR | 电晶体 |
| 676 | TRANSMISSION | T/M | 传动装置 |
| 677 | TRIM PANEL | T/PNL | 调整板 |
| 678 | TRUNNION | TRUN | 目轴 |
| 679 | TURNBUCKLE | T/BKL | 套筒螺母 |
| 680 | TURN SIGNAL | T/SIG | 转移信号 |
| 681 | TYPICAL | TYP | 特有的 |
| 682 | ULTIMATE | ULT | 顶点(基本原理) |
| 683 | ULTLMATE TENSILE STRENGTH | UTS | 最大张力 |
| 684 | UNDER BODY | U/BODY | 底部 |
| 685 | UNDERCUT | U/CUT | 从下边切球 |
| 686 | UNDERSEAT | U/SEAT | 下方座椅 |
| 687 | UNDERSIZE | U/SIZE | |
| 688 | UNIFORM PARTS CLASSIFICATION | UPC | |
| 689 | UNIFORM PARTS GROUPING | UPG | |
| 690 | UNIVRESAL | UNIV | |
| 691 | UNIVERSAL JOINT | U/JNT | |
| 692 | UPPER | UPR | 上面的 |
| 693 | USED WITH | U/W | 沿用 |
| 694 | VACUUM | VAC | 真空 |
| 695 | VALVE | VAL | 气阀,活门 |
| 696 | VENTILATOR | VENT | 气孔 |
| 697 | VENT WING | V/WING | 气孔翼 |
| 698 | VERTICAL | VERT | 垂直 |
| 699 | VOLTAGE REGULATOR | V/REG | 电压调整器 |
| 700 | VOLUME | VOL | 量 |
| 701 | WARNING | WRNG | 警告 |
| 702 | WASHER | WA | 垫片 |
| 703 | WATER PUMP | W/PUMP | 抽水机 |
| 704 | WEATHERSTRIP | W/STRIP | 雨刷 |
| 705 | WEIGHT | WT | 重量 |
| 706 | WELD NUT | W/NUT | 焊接螺帽 |
| 707 | WHEEL | WHL | 轮子 |
| 708 | WHEELBASE | WB | 轮胎底部 |
| 709 | WHEEL BEARING | W/BRG | 轮胎轴承 |
| 710 | WHEELHOUSE | W/HSE | 轮胎? |
| 711 | WHITE SIDE WALL | WSW | |
| 712 | WINDOW | WDO | 窗户 |
| 713 | WINDOW REGULATOR | W/REG | 升降机 |
| 714 | WINDSHIELD | W/SHLD | 挡风玻璃 |
| 715 | WINDSHIELD WASHER | W/WSHR | 漏水器 |
| 716 | WINDSHIELD WIPER | W/WPR | 前雨刷 |
| 717 | WIPER | WPR | 雨刷 |
| 718 | WIRING | WRG | 配线 |
| 719 | WIRING DIAGRAM | W/DIAG | 配线图 |
| 720 | WITH | W/ | 具有 |
| 721 | WITHOUT | W/O | 不具 有 |
相关推荐
友情链接
Copyright © 2023 All Rights Reserved 版权所有 商丘润滑油价格联盟